PDA

View Full Version : 1996 - 1998 Mustang Cobra

Pages : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 [55] 56 57 58 59


  1. Doing DOHC swap few small questions.
  2. Dumb question?
  3. what do you think guys?
  4. torco or race gas
  5. Lash Adjusters-oem Vs Trick Flow
  7. bhead or chead....help me decide
  8. fuel pump?
  9. putting 2001 cobra motor in 1998 cobra??
  10. vortech v-2 SQ GT kit to my Cobra?
  11. Stage 3 ported B's or Mach 1 heads?
  12. 11" flywheel require different starter?
  13. Welding up axle tubes what jig to use?
  14. What turbo's to go with?
  15. Will this rear end fit/ be the same?
  16. N/A Mark VIII build
  17. need help!! car not doing so well
  18. Help: 4v Swap!!
  19. IMRC Deletes
  20. need help with 04 head swap
  21. vortech in-line pump
  22. Thump Racing Tensioner for Vortech S/C
  23. Drove her today
  24. Comp cams owners in here!!!
  25. stock mid pipe.. 10 series or super 44 s
  26. Secondary air injection
  27. Second thoughts
  28. bottom end help?
  29. Exhaust Help
  30. High compression 5.4?
  31. Stock T-45 Track Times
  32. Coil Pack Question
  33. lifter tick 97 cobra
  34. throttle body gasket...
  35. Gear Ratio Question
  36. Fly cut piston tops?
  37. Best blower cams?
  38. Shelby GT 500 seats in a Sn-95?
  39. Need alt wiring help
  40. intake cam
  41. finishing bolt ons - missing anything?
  42. camber bolts or plates?
  43. 1996 Cobra F1a Where Is My Power
  44. Can some one help??
  45. 4.6 Dohc ysi intercooled build question
  46. I need some help swapping heads/cams
  47. rear drag wheel choices
  48. Help needed please
  49. KB 10-12#'s of boost.42 lb inj enough?
  50. fuel tank questin
  51. head porting...Livernois?
  52. Will a Eaton Swap fit under stock hood?
  53. Last 1. COP/ '03 valve covers
  54. Stage 3 Crower Blower Cams Degree
  55. Quick header question.
  56. Thoughts on Hydrolock? Long post sorry.
  57. Stock maf programmability?
  58. Header choice
  59. 8 or 10 pt roll cage choices
  60. 04 cobra supercharger on a 98 cobra
  61. Cross-drilled and/or Slotted...
  62. Question about cam timing
  63. Almost done..
  64. UPR K-Member/Lakewood 40511 90/10 combo
  65. overheating questions
  66. Places to by NEW 97 Mustang Cobra Parts
  67. do i have enough fuel system?
  68. How much hp will I make?
  69. 99-01 cobra motor in a 97 cobra?
  70. Why is the 96/97 Cobra harness diferent?
  71. Which spark plug wires for 700rwhp?