Activity Stream
-
Older Activity
-
Yesterday, 06:48 PMGlad I could pass that along, hopefully as clearly and concisely as possible. No sense in paying $60+ for something on-line when anyone can knock it...3 replies | 158 view(s) -
Yesterday, 06:55 AMHi everyone, I recently obtained a pristine Bullitt and being old enough to remember the movie, am open for advice from all. 1st question -...0 replies | 42 view(s) -
08-10-2020, 07:25 PMThanks for sharing!!!3 replies | 158 view(s)
-
08-08-2020, 09:12 PMThanks Joe! This will be a nice upgrade for any Terminator and your DIY instructions like always are easy to read and use. Ed3 replies | 158 view(s) -
08-08-2020, 01:10 PMHaven't been spending a lot of time on forums lately due to being busy with life plus the general insanity of 2020. One of my side projects that I...3 replies | 158 view(s)
-
08-08-2020, 02:07 AMI second Ed’s post. Hands down the best and when you total up the cost of rings and precision involved, the cheapest!2 replies | 110 view(s) -
08-06-2020, 09:06 PMsold pretty cheap2 replies | 694 view(s)
-
08-06-2020, 08:53 PMOscar929rr replied to a thread For Sale 01 Twin Turbo Saleen with Lots of Extras. *MUST SEE* in Vehiclesnice car, GLOTS1 replies | 161 view(s)
-
08-06-2020, 10:30 AMMatt, this is an excellent staging device and it takes a lot of the abuse the engine and drive train are typically subjected to during staging and...1 replies | 69 view(s)
-
08-06-2020, 05:20 AMJamesHell replied to a thread Crank stud mod question? possible problem. in 2003 - 2004 SVT Mustang CobraJust back the stud out what's needed to clear the nut. That small amount won't effect the strength. I am betting the hole got into the oil galley...2 replies | 368 view(s) -
08-06-2020, 03:45 AMHey all, finally got my boost and launching dialed in and going to start actually becoming competitive. I’m running a fmvb with transbrake and...1 replies | 69 view(s)
-
08-05-2020, 09:24 PMCheck-out the Gibtec pistons. The best out there and fairly priced. Ed can give you all the details about them. ...1 replies | 70 view(s) -
08-04-2020, 09:32 PMOl_red2000gt has created a new vehicle in the garage. Go check out their 2000 Ford Mustang Gt!0 replies | 58 view(s) -
08-04-2020, 09:28 PMso im rebuilding my drift mustang after the engine developed a rod knock, how ever im new to building engines and i plan on putting around 10 to 12...1 replies | 70 view(s)
-
08-03-2020, 02:37 PMTotal Assignment Help provides best quality Case studies, our bbc case study is the one of best case study help out 1000 of students to understand...1 replies | 71 view(s)
-
08-02-2020, 11:39 PMwebdancer has created a new vehicle in the garage. Go check out their 2001 FORD Mustang V6 Premium / Pony Package!1 replies | 71 view(s)
-
08-01-2020, 02:39 PMIt's official, selling my Twin Turbo Saleen. I’ve owned the car since 2004 and its has been enjoyed and I have shared its progress with you all via...1 replies | 161 view(s) -
07-31-2020, 12:58 PMI worked a deal with Gibtec a umber of years ago to build custom billet pistons with tool steel pins, and TotalSeal rings, your choice of pin locks...2 replies | 110 view(s)
-
07-31-2020, 09:46 AMIt doesn’t pull timing, just bleeds off boost, but you are correct, if target is 20, having it around 22-23 would be safe. It’s not going to hurt the...10 replies | 460 view(s)
-
07-31-2020, 08:37 AMIf it pulls timing as a safety function you may want to raise that value a few more psi b/c of boost fluctuation/spikes. ks10 replies | 460 view(s) -
07-31-2020, 06:47 AMThe warning is maximum boost you don’t want to exceed, it is a psi value. The limiter value is a percentage of how much to retard boost once the...10 replies | 460 view(s)
-
07-31-2020, 06:39 AMWhat does the Warning do? ks10 replies | 460 view(s)
-
07-31-2020, 12:32 AMI made a cheat sheet based on the two threads I’ve found in the internet, one was from a Mitsubishi forum, another from a Mazda forum. If the...10 replies | 460 view(s)
-
07-30-2020, 03:01 PMI am trying to find a set of pistons for a project that will net me 11.5 to 1 static comp for a turbo 4v application on methanol. Looking to spend...2 replies | 110 view(s)
-
07-29-2020, 03:54 PMFrom my research, the start boost value is actual psi, so I’m thinking if I don’t have a value over 15psi (the spring) it won’t make any more boost. ...10 replies | 460 view(s)
