Search Results - Mustang Forums and Ford Performance Forums at ModularFords

Search:

Type: Posts; User: lazer97gt; Keyword(s):

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    323

    I got the car running with the new full manual...

    I got the car running with the new full manual VB. Even with auto trans turned off in the tune just like you would do for a manual trans swap, the computer will still recognized when the car is in...
  2. Replies
    2
    Views
    323

    4r70w tuning from auto VB to FMVB

    Hi! My car have a 4r70w with j-mod VB and tuning the car with sct prp. I'm about to install a full manual valve body with transbrake. I'm wondering what i have to change in my tune. Sct say to turn...
  3. Thanks I appreciate. Car run much better now. Do...

    Thanks I appreciate. Car run much better now. Do you happen to know where i could find the multipliers for the injectors ? I'm running stock fuel pressure for now but i will maybe try some E85 later...
  4. marauder aviator 24# injectors calibration data

    Anyone have hi-slope , low-slope, ect data for marauder 24#injectors? I've tried a few data from different injectors on the ford racing site but almost all 24# injectors seems to be way off. The...
  5. Replies
    53
    Views
    6,036

    How about installing cam bearings ? Dura-bond...

    How about installing cam bearings ? Dura-bond part# FA-4
  6. Need help wiring fuel pressure sensor to SCT X3 for datalogging

    Hi! I want to datalog fuel pressure using the analog output from my sct X3. I'm using a 0-100psi autometer sensor part# 2246 0-5V.


    1 - I will take my 5V source from the TPS sensor
    2- signal...
  7. Replies
    4
    Views
    1,346

    Thanks! Do i completely torque the main stud (3...

    Thanks! Do i completely torque the main stud (3 steps) and then do the side bolts ? Or do step1 on main studs , do step1 on side bolts , step2 on main studs, step 2 on side bolts ect..
  8. Replies
    4
    Views
    1,346

    Aluminator and wap main stud torque sequence

    Is it the same torque sequence than the teksid except skipping the jack screws ? Mine is actually a late teksid with 9mm side bolt like the wap block. I only found the sequence for the teksid with...
  9. Replies
    5
    Views
    938

    Not sure if you're using the older version of the...

    Not sure if you're using the older version of the wot box with window switch cable or newer version with progressive controller. I have the older version and using the window switch cable to control...
  10. Replies
    782
    Views
    235,476

    Thanks Ed! So no issue using a single oil feed...

    Thanks Ed! So no issue using a single oil feed hole bearing in aluminum block ? I tought that the second oil feed port would have to be cut on the flanged upper.

    Also do you happen to have pics of...
  11. Replies
    782
    Views
    235,476

    I have a question regarding the flanged #5 upper...

    I have a question regarding the flanged #5 upper main bearing ( king F5219U). I see one oil port on the bearing which i assume is for a an iron block compare to 2 oil port for aluminum block. Any...
  12. Anyone have experience tuning the 4r70w with PRP

    Hi! I'm trying to adjust my wot shift point and it seems like my trans does not respond well to any change done in the RPM based shift point. It seems to work better if i change the setting in the...
  13. For Sale Sold!!!!!

    Sold!!!!!
  14. For Sale to the top or best offer

    to the top or best offer
  15. Replies
    6
    Views
    1,351

    Just found 1 .63 housing for cheap. I will try to...

    Just found 1 .63 housing for cheap. I will try to find another one or trade one of my .48 for a .63. A very knowlegdeable local turbo shop told me to go on the small side since i have no transbrake...
  16. Replies
    6
    Views
    1,351

    It's not as easy as just dropping the pan and...

    It's not as easy as just dropping the pan and changing valve body. The transmission was built with 3 friction in the reverse drum.
  17. Replies
    6
    Views
    1,351

    Hp twins turbine A/R size?

    Installing HP twin kit. Turbo's are Billet T04E 58mm (60trim) , T3 hotsides StageIII wheel (65/56 mm) I'm hesitating between a .63 and .82 a/r turbine housing. Rest of the setup is 4.6 , 10:1 CR ,...
  18. For Sale Mechanical single blade throttle body for GT500 or coyote cobra jet intake

    This an accufab 03

    - - - Updated - - -

    This an accufab 03-04 cobra mechanical throttle body that was modified to the GT500, cobra jet bolt pattern. Need to use remote iac as the iac passage was...
  19. Wanted WTB/WTT T3 .63 a/r turbine housing for stage 3 wheel

    Looking for a pair of T3 .63 a/r turbine housing, 4 bolt downpipe exit , that will fit a stage 3 wheel. I currently have a pair of garrett .48 that i could trade. Will consider .58 a/r housing as...
  20. Replies
    12
    Views
    9,205

    Maybe the sleeve length could cause some problem....

    Maybe the sleeve length could cause some problem. The throttle body body on the 03-04 cobra is further from the bracket but maybe the sleeve is shorter. Does your bullit cable fit from bracket to...
  21. Replies
    12
    Views
    9,205

    It's too long.

    It's too long.
  22. Replies
    12
    Views
    9,205

    I was in the same boat as you and i ended up...

    I was in the same boat as you and i ended up finding one at a reasonable price. I wanted to modify an 03-04 cobra cable. it's probably one of the longest cable available and can be found for 60$ on...
  23. Replies
    2
    Views
    505

    Thanks. I started my project earlier then i...

    Thanks. I started my project earlier then i tought. Found a set of continental heads last monday, bought a complete eaton swap localy tuesday and started the swap last thursday. I should ear the...
  24. Replies
    1,096
    Views
    268,267

    If i read correctly, it's with a 2.76 upper 4 #...

    If i read correctly, it's with a 2.76 upper 4 # lower ??? Any boost drop at higher rpm ? Where did it peaked?
  25. Replies
    1,096
    Views
    268,267

    When will these kits be available?

    When will these kits be available?
  26. Replies
    2
    Views
    505

    Newbie from canada

    Hi! I own a 97 GT with 97 cobra engine with basic bolt-on. I've been hanging on mustang forums for years but never posted. I'm looking to swap to C heads and do an eaton swap in the next year so i'm...
Results 1 to 26 of 26