Search Results - Mustang Forums and Ford Performance Forums at ModularFords

Search:

Type: Posts; User: eschaider; Keyword(s):

Page 1 of 13 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    41
    Views
    888

    I am not certain about the TunerStudio version...

    I am not certain about the TunerStudio version status but this is what I suspect. The lite version is a freebee and other than registration has no other licensing requirements I am aware of. The...
  2. Replies
    41
    Views
    888

    The base tune is expecting to find a stock...

    The base tune is expecting to find a stock returnless fuel system, Josh. You will have to go into the tune and modify it for a return style fuel system.

    Here is a pic from the TunerStudio s/w...
  3. Replies
    41
    Views
    888

    If it is stock boost gauge line then you are...

    If it is stock boost gauge line then you are obviously good to go.



    Ed
  4. Replies
    41
    Views
    888

    If that line is in fact sourced after an hvac...

    If that line is in fact sourced after an hvac check valve, Josh, then Ashford is spot on. If it is being sourced off your intake, just make sure you are getting it from a location that is post rotor...
  5. Replies
    41
    Views
    888

    Each time I engage with these folks, Ken, I walk...

    Each time I engage with these folks, Ken, I walk away more impressed than the time before.

    Extraordinary product with extraordinary people!

    Such a breath of fresh air.



    Ed
  6. Replies
    41
    Views
    888

    When we buy a performance part or component we...

    When we buy a performance part or component we are fairly well conditioned to a maybe, congratulations or good luck sort of commentary from the supplier.

    I want to share the MS3Pro PnP email I...
  7. Replies
    41
    Views
    888

    To each his own Eric. As has been said before...

    To each his own Eric. As has been said before beauty is in the eye of the beholder. While both approaches have their positives and negatives, in the end beauty is infact in the eye of the beholder. ...
  8. Replies
    41
    Views
    888

    I know, Robert. Sean always occupied the high...

    I know, Robert. Sean always occupied the high priced ground which I didn't mind if I was getting value for my money. Turned out it wasn't the case, at least with the blocks. More investigation is...
  9. Replies
    41
    Views
    888

    Tommy, They have a live link on the site to...

    Tommy,

    They have a live link on the site to download the tune file now if this trick I am going to try doesn't work. I have attached a copy of the unmodified tune file for the Terminator. The...
  10. Replies
    41
    Views
    888

    My receipt reads identical to yours, Ken. It is...

    My receipt reads identical to yours, Ken. It is the Terminator version. Your tune file will be named 03 Cobra 40lb inj final.msq. Just like the naming convention implies the tune file is setup to...
  11. Replies
    41
    Views
    888

    Thanks for the kind words, Ken. Sometimes the...

    Thanks for the kind words, Ken. Sometimes the luck of the draw is not what you might have expected. That said, I was lucky enough to find a used standard bore Aluminator block in NJ that is in...
  12. Replies
    41
    Views
    888

    They don't, Ken. The problem is one of...

    They don't, Ken.

    The problem is one of possibly two different whoopses, hopefully not both but possibly both. The first could be that the heat treat on the block was done incorrectly and the...
  13. There are still folks on the Forum Parker...

    There are still folks on the Forum Parker however, they tend to have already built their engines and do more observing than posting. Additionally the bulk of them tend to be in the Terminator forum...
  14. Replies
    41
    Views
    888

    Thanks for sharing, Kevin. Whenever we start...

    Thanks for sharing, Kevin.

    Whenever we start out on a new technology initiative it is always helpful to see how someone else approached a similar challenge. The opportunity to learn from...
  15. Replies
    41
    Views
    888

    I have had a minor setback on the engine, guys. ...

    I have had a minor setback on the engine, guys.

    I was torquing the heads down this last weekend when one of the ARP studs pulled all the threads out of the head stud bolt well. Yuppers, clean...
  16. Somehow I just know you are going to be the first...

    Somehow I just know you are going to be the first out of the gate, Josh. :)


    Ed
  17. Thanks for the heads up Jerry and thanks for the...

    Thanks for the heads up Jerry and thanks for the extraordinary job of productizing the PnP version of the MS3Pro. I have worked with several of your team, Ben, Eddie and John in particular, and the...
  18. Replies
    41
    Views
    888

    MS3Pro Terminator Version Arrives!!

    It looks like Santa Claus came early last night. As I went out to pick up the mail I found a package on the porch and it was from DIYAutoTune. This is what it looked like;

    170475

    When you open...
  19. Jerry, The reason you couldn't find it was...

    Jerry,

    The reason you couldn't find it was their new website has not gone active yet. They expect the website to be up later this week so my my guess is probably Thursday or Friday if you go over...
  20. Very nicely done, Kevin. That is exactly the...

    Very nicely done, Kevin.

    That is exactly the plumbing model I was trying to describe a half dozen or so posts back. Simple, straightforward and best of all it just works!


    Ed
  21. I am amazed at how you get early access to as yet...

    I am amazed at how you get early access to as yet unannounced parts, Jim. :)

    The sensor Jim is talking about is a sweetheart piece, this is what it looks like;

    170457

    And you can see it is...
  22. I think you will be fine and also have a very...

    I think you will be fine and also have a very enjoyable fun to drive car, Ken.


    Ed
  23. Good points Kevin, especially the knock...

    Good points Kevin, especially the knock detection. Both MS and John (Vampire) do a good job of detecting the presence and the offending cylinder. I need to dig into the MS approach deeper to better...
  24. Ken, Discretion is the better part of valor...

    Ken,

    Discretion is the better part of valor here. I would run at least 10:1 compression and put an arbitrary ceiling on compression at 11:1. With the potential to see 93 octane the 10:1 c/r wold...
  25. Just an FYI for anyone thinking about getting one...

    Just an FYI for anyone thinking about getting one of these units, they can be ordered off the website right now. Here is the link => MS3Pro PnP Terminator Version

    DIYAutoTune thought they had...
  26. You will get excellent power numbers from ethanol...

    You will get excellent power numbers from ethanol at almost any compression ratio from 9:1 on up the scale even into the thin air around 13:1, Ken. The real benefit(s) of the ethanol are the high...
  27. The sensor will work in either the feed or return...

    The sensor will work in either the feed or return lines, Ken. The easiest way to do the parallel plumbing is to use "T" or "Y" fittings to split off a second delivery or return path. The primary...
  28. The Bluetooth adapter makes the tuning and data...

    The Bluetooth adapter makes the tuning and data logging very nice. It is sort of like the step up from wired ethernet to the Internet vs WIFI w/o the need to drag around an ethernet cable. If I am...
  29. As I understand it, Josh, it is run in a short...

    As I understand it, Josh, it is run in a short but parallel path with the main fuel line. The sensor I keep hearing the most about is the GM sensor but I suspect you could use any of the OEM quality...
  30. Hendri, I showed the guys at DIYAutoTune your...

    Hendri,

    I showed the guys at DIYAutoTune your post. You had them rolling on the floor laughing!

    If you want one out of the first production run get in line quickly because the entire first...
  31. Awesome, Josh. I knew there was a big backlog...

    Awesome, Josh. I knew there was a big backlog which is why I twisted your tail. I am glad you made it into the first production run.


    Ed
  32. You are going to be able to order it directly off...

    You are going to be able to order it directly off the website, Ken. Based on discussions I have had with the development team the site will be alive for ordering next week potentially as early as...
  33. I believe the switched approach will work with...

    I believe the switched approach will work with the MS3Pro because the doc says it will. I am not confident it will work with the OEM TC because that was in the factory ECU which is no longer in the...
  34. For those inquiring minds, Jerry is Jerry...

    For those inquiring minds, Jerry is Jerry Hoffman. Jerry is the man who started DIYAutoTune and AMP/EFI specifically to sell the finished goods fully assembled versions of the MegaSquirt EFI system...
  35. I was speaking with their development team...

    I was speaking with their development team manager yesterday, Ken. At the time he told me the Terminator version was complete and they were finishing up the arcane internal paperwork stuff that...
  36. I haven' t read up on it more and of course it is...

    I haven' t read up on it more and of course it is always nice to have a test bed to experiment with to get a better understanding of the system. If I have read the manual correctly it appears that...
  37. Yes and no, Ken. The MS3Pro will use the rear...

    Yes and no, Ken. The MS3Pro will use the rear VSS signals. The front VSS signals will require a Hall effect sensor to be mounted to the wheel of choice for monitoring purposes. My suggestion would...
  38. Sorry we didn't connect, Daniel. What a bummer,...

    Sorry we didn't connect, Daniel. What a bummer, you AJ and I were all there!

    On a track that is prepped like BG was you can throw full timing at it right from the hit as long as it does not...
  39. Replies
    9
    Views
    334

    If the two nicks in the red circle below are what...

    If the two nicks in the red circle below are what you are talking about, Russ, the answer is they are fixable. You do not file them down. Instead you want to use an Exacto knife and just cut off the...
  40. Daniel, I was Bowling Green with AJ this...

    Daniel,

    I was Bowling Green with AJ this weekend and his car is similar to yours. It's a shame we didn't bump into one another. Some likely differences between his car and your car are fuel; he...
Results 1 to 40 of 500
Page 1 of 13 1 2 3 4