Search Results - Mustang Forums and Ford Performance Forums at ModularFords

Search:

Type: Posts; User: Last Man Standing; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.04 seconds.

  1. Mine started doing it too.

    Mine started doing it too.
  2. I have no experience with this. I would talk to a...

    I have no experience with this. I would talk to a manufacture of a shorter control arm to pick their brain.
  3. Fox body arms are one inch shorter. You could run...

    Fox body arms are one inch shorter. You could run those and a spacer to get the offset you want.
  4. Replies
    2
    Views
    772

    I have their 15x10s and it hit the banjo bolt for...

    I have their 15x10s and it hit the banjo bolt for the brake caliper. They state on their website that you will have to grind down the bolt. I didn't want to do that so I bought a rear brake line kit...
  5. Replies
    5
    Views
    1,292

    Get the intercooled version and don't look back. ...

    Get the intercooled version and don't look back. With the non-intercooled version during the hot months the intake air temps will get so hot the tune will pull timing and the car will feel as slow...
  6. Replies
    1
    Views
    556

    I ran a promotion 3650 for seven years. Never had...

    I ran a promotion 3650 for seven years. Never had a problem. Call them they are good people to deal with.
  7. Replies
    5
    Views
    947

    The tire company list the rim range for each...

    The tire company list the rim range for each tire. As long as you are within that range you will be fine.
  8. Replies
    8
    Views
    1,430

    Put a boost a pump on it.

    Put a boost a pump on it.
  9. Check with VMP tuning, they are in Florida. With...

    Check with VMP tuning, they are in Florida. With remote tuning you will need to get your wide band installed and set up for data logging, you have to know what the a/f is at wot. Some where on the...
  10. Replies
    52
    Views
    7,940

    It's because of the bypass not recirculating when...

    It's because of the bypass not recirculating when not in boost. No such thing as to much recirculating. Just put it back together the way kenne bell designed it. Are you sure the fluid is...
  11. Replies
    52
    Views
    7,940

    You need to put the Kenne Bell bypass valve and...

    You need to put the Kenne Bell bypass valve and tube back on. You cant use a blow off valve like you are doing on that blower. Kenne Bell even says your not supose to run a blow off valve. You need...
  12. Replies
    225
    Views
    30,031

    If the air fuel ratio is going lean at off or...

    If the air fuel ratio is going lean at off or part throttle it will cause a misfire or stumble.
  13. Replies
    5
    Views
    972

    Cut it and then measure the length with a tape...

    Cut it and then measure the length with a tape measure.
  14. Replies
    5
    Views
    972

    Your old belt will have a number on it .

    Your old belt will have a number on it .
  15. Hey svt Troy, how loud is your jabsco pump? I'm...

    Hey svt Troy, how loud is your jabsco pump? I'm thinking about getting one and putting it in the trunk. I don't want one that is loud. I drive my car often.
  16. Replies
    4
    Views
    1,014

    Why are you wanting to run spacers? The wheels...

    Why are you wanting to run spacers? The wheels fit with no spacers. If you run a 25mm spacer on the rear, the wheel will stick out past the wheel well.
  17. Replies
    5
    Views
    866

    I would check crank thrust.

    I would check crank thrust.
  18. Check out the-fan-man.com, they have a large...

    Check out the-fan-man.com, they have a large selection of fans. I have bought from them.
  19. Replies
    6
    Views
    719

    Sounds like a bad fan motor. After the fan runs...

    Sounds like a bad fan motor. After the fan runs and then stops unplug it and check for power and ground with a test light across the terminals. If the test light comes on, I would replace the fan...
  20. Replies
    15
    Views
    3,337

    Check rockauto.com

    Check rockauto.com
  21. Replies
    26
    Views
    10,285

    No meth or killer chiller. I do run a bottle of...

    No meth or killer chiller. I do run a bottle of Lucas or NOS octane booster with the 19psi pulley. The 19psi pulley is for the track, where it is easier to keep intake air and engine coolant temp in...
  22. Replies
    26
    Views
    10,285

    I'm running stock compression, 93 octane pump...

    I'm running stock compression, 93 octane pump gas, 16 degrees timing. The inlet came off a 2.6/2.8 KB.
  23. Replies
    26
    Views
    10,285

    It made 598rwhp @ 19psi, the blower is maxed out...

    It made 598rwhp @ 19psi, the blower is maxed out spinning 18,036rpm at 6400engine rpm. On low boost it made 528rwhp @ 13psi.
  24. Replies
    26
    Views
    10,285

    I'm running MHS stage 2 heads with MHS stage 1...

    I'm running MHS stage 2 heads with MHS stage 1 blower cams. Made 598rwhp and 580rwtq with a KB 2.1 with a 2.6 inlet. Peak power came in at 6300rpm. Driveability is perfect.
  25. Replies
    8
    Views
    1,710

    Most people will say the steel backed guides are...

    Most people will say the steel backed guides are better. With having said that I went with plastic guides when I built my engine 5 years ago. I recently put heads and cams on the engine and saw...
  26. Replies
    8
    Views
    1,710

    I had the same problem with a Cloyes chain set I...

    I had the same problem with a Cloyes chain set I used when rebuilding my engine. I had a stock Ford chain laying around and installed it. Everything fit perfect. Buy new Ford chains or reuse the ones...
  27. Replies
    1
    Views
    1,036

    For Sale Open to offers.

    Open to offers.
  28. Replies
    1
    Views
    1,036

    For Sale L&M throttle body

    L&M Airflow duel blade 66mm throttle body for Shellby GT-500.
    $500 plus shipping add 3% for PayPal fees.
    932959329693297
  29. Replies
    8
    Views
    1,592

    The 103s are a great plug. I run them in my stang...

    The 103s are a great plug. I run them in my stang and never had an issue. I'm at 598rwhp, pump gas, stock coils.
  30. Replies
    16
    Views
    2,310

    I run autolite AR103 gapped at .030, stock coils,...

    I run autolite AR103 gapped at .030, stock coils, 19.5psi, 598rwhp. Never had a problem.
  31. Replies
    25
    Views
    3,662

    Thanks , I really appreciate you looking into...

    Thanks , I really appreciate you looking into this and helping out.
  32. Replies
    25
    Views
    3,662

    PCM code is G1Z2. This is the code on the sticker...

    PCM code is G1Z2. This is the code on the sticker of the PCM .
  33. Replies
    25
    Views
    3,662

    Not sure what you mean by PCM code.

    Not sure what you mean by PCM code.
  34. Replies
    25
    Views
    3,662

    neutral rev limiter

    Having a issue with my neutral rev limiter. I have a custom tune on an xcal3. The problem is where ever I set the neutral rev limiter it is also limited to that rpm in drive. Can someone make an...
  35. Replies
    361
    Views
    102,768

    Here is my 598rwhp 2.1 KB with a 2.8 inlet, MHS...

    Here is my 598rwhp 2.1 KB with a 2.8 inlet, MHS stage 2 heads and MHS stage 1 blower cams.
    9270192702
  36. Replies
    8
    Views
    2,274

    I have three mods that were free to me but can be...

    I have three mods that were free to me but can be done for under $30 each.

    Adjustable clutch pedal stop. I welded a lock nut to clutch pedal.
    92698

    Clutch pedal height stop.
    92699

    I made...
  37. Replies
    17
    Views
    5,644

    I would disconnect everything that is connected...

    I would disconnect everything that is connected to the 5v circuit. Then check the voltage, if it is still the same, I would disconnect that circuit from the pcm and then check the voltage on that...
  38. How high are your temps?

    How high are your temps?
  39. Replies
    10
    Views
    3,090

    The compression and camshafts are probably...

    The compression and camshafts are probably different.
  40. Replies
    109
    Views
    20,652

    http://img.tapatalk.com/d/13/09/02/e3yty7u2.jpg ...

    http://img.tapatalk.com/d/13/09/02/e3yty7u2.jpg

    Isn't hard to drive a race car in high heels. j/k
Results 1 to 40 of 419
Page 1 of 11 1 2 3 4