Hey guys, just got motor put back in after we had coolant getting into the oil on this fresh build. Got it started and it started right up but was running really ruff. let it idle for about 30 seconds and killed it. Went to start again and it was hard to start but idled. we decided to kill it...
Lightning m112 complete from lower manifold to fuel rails and injectors $1000
tr3650 05-09 stage 4 clutch and hurst shifter included $900
03-04 cobra lower supercharger manifold $400
mhs stage 4 naturally aspirated cams $500 less than 1200 miles on these
I have a lower supercharger manifold off a 03 04 cobra thats in perfect conition-$400. 2 sets of 4v B heads bare or with cams so i will seperate if desired $225 set of bare heads, and $100 for cams. Together $300 for heads and cam together. Thank you.
Hello to all!!!
I own a 2010 Saleen 435 S and I am looking to continue adding performance upgrades to the vehicle. So far I have added the following:
Kooks long tubes and high flow cats
Smaller SC pulley, 3.6 in., approx. 7.b lbs. boots
Series colder spark plugs
Brenspeed Custom Tune...
Comp Cams XE270AH 2V cams for 4.6 5.4. These have NEW Ford sprockets and bolts, torqued and ready to go. Looking for $550 shipped. I have pics but don't know how to upload here. Email [email protected] Don't PM or reply here becuase I may not get it soon, email is best. These cams can be...
I'm at a crossroads with what I want to do for my Spring build. I'm kind of torn between going with a big blower or getting a small blower and putting money in cams/heads. I know doing the cams/heads would be a little more money and would probably end up with very similar...
I am having issues w/ the comp cams stage 2 XFI-SPR cams with cam phaser limiters. Timing for them isn't getting set right this is the second shop I have taken the car too and they are having issues as well. The shop knows there stuff they have 3 stangs running over 1k hp each so im sure they...
I keep hearing oh its not as good as it sounds oh its under rated my ls1 will take it. The mustang will never be on top. Well i have been looking at forms and driving cars and racing for a while and im not biassed, not at all. I have had a ls1 before and its a great motor! But i dont see any...
HPP Billet Blower cams. No need for Shims.
.474" lift 282* duration 114 ls.
Ran one season. 130 passes 20 dyno pulls. Made 720 hp with a conservative tune through a C4.
$1100 + ship
PM me please.
I have a 96 Cobra I just bought and the bottom end is still together but the heads are off the motor. Car was getting hot I was told. I am not sure if they burped the motor when they refilled the radiator as the person who owned the car does not know much at all about motors. I am going to have...
Set of used Stage 2 ported cylinder heads that come fully assembled with a set of Comp Cams "Thumper" camshafts (part# 127020). These only have 1600 miles on them. Off the car and ready for shipment. Feel free to PM or call me with any questions @ 405 207 7737
hey guys to much stuff cluttering up the garage would like to get rid of some of it, ill post a list just make and offer on what you need thx.
96-98 timing cover
96 mark viii b heads/ w cams
03 cobra cams low mileage 35k
01 cobra cams low mileage 10k
1 set of primary gears
I'm selling a set of Comp Cams 3v Stage 2 blower cams. Was told they have less than 3000 miles on them. They look good, but I still sent them to machine shop to polish the journals so they are like new again.
Asking $500. Cams are $700 new. May also trade for good forged crank for factory...
I am looking to buy some cams for my my Mustang but Im not sure which cams are the best for it. Are the comp cams XFI™ SPR, XE264PH-12 or the trickflow cams TFS-51802002 the best for my Mustang? Can anyone help?
Its got a couple things done to it. I bought it from a lady that thought it was stock...
47K miles, cams (unknown), mac longtube headers, mac high flow cats, mac mass air meter, flowmaster catback, steeda springs, lowered, K&N CAI, steeda tri-ax short throw shifter, and a few other nick nacks...